[ Chinese wardrobe net ] When you buy a wardrobe , sometimes you don't buy the finished wardrobe that you have assembled, but the type of wardrobe that you need to assemble yourself.
At this time, we all need to do our own assembly work in this area. Xiaobian today will give you a brief introduction to the method steps of the wardrobe assembly.
Concrete steps for wardrobe assembly
1. Check the packaging: When receiving the goods, whether it is express or direct purchase, be sure to check whether the packaging is seriously damaged.
If there is, it is likely that the steel pipe inside is also crushed. Such goods must not be signed and purchased, so be sure to check clearly.
2. Check the accessories: Open the package, and then check whether the accessories inside are complete. According to the instructions, if there are few, you must find the customer service in time to replace it. Always wear gloves when you install it.
3. First install the bottom: first install the bottom one is the middle, take out the four-way joint with the bottom and the high, and connect with the short tube in the middle. Install a four-way joint on each side, then install the tube on both sides, and decide the position to be placed. Install a long tube on one side and a short tube on the other. Then install the base fabric on both sides and install a three-way joint on each side.
4. Set of wardrobe cover: After installing the bottom, insert six short steel pipes, and then put the whole wardrobe cloth on the surrounding holes. Refill a layer of baffles like the bottom and place it on six steel pipes.
5. Install the short-side floor: If the wardrobe is divided on two sides, first install the short-side floor, first insert the side steel pipe, then install the cloth, then connect the four-way joint, install two horizontal steel pipes, and install Separate the cloth and make up the four-way joint on both sides. Repeat the baffle until it is attached to the top.
6. Long-side steel pipe: After the short-side partition is installed, the long side is a vertical hanging area, and a three-way joint is used to connect the two long pipes to the top.
7. Install the top steel pipe: After both sides are installed, connect them directly with long steel pipes, so that the wardrobe is installed. If the wardrobe is too high and not enough to squeeze, it is recommended to push the side back so as not to be installed. At the same time, the hanging steel pipe can also be installed with a hook type joint, which is relatively simple.
8. Set of wardrobe cover: When the top of the large set is on the top, it is best to pull the bottom to the top, so that there is space to pull up, until the upper corner is installed diagonally. At this time, the cloth cover can be pulled down.
Second, the wardrobe assembly notes
1. Wardrobe assembly preparation: Many simple wardrobes that have been bought have a simple wardrobe with a number of steel pipes, which can be put together with the same number.
Then find out the parts of the simple small wardrobe chassis and put them together. Note that it is only the bottom part of the simple wardrobe.
There are some simple small wardrobes with shoe racks, you must first install the simple wardrobe shoe rack. Then, the bottom of the simple wardrobe board is installed in a number of places, and then the simple wardrobe is classified into pieces, and finally the position of the simple wardrobe classification board is placed.
2. The front of the wardrobe assembly: When assembling, the simple wardrobe body is facing down, and the simple wardrobe is installed from left to right or from right to left. After assembling the simple wardrobe panel, please ensure that the diagonal error of the cabinet is Within plus or minus 1MM.
After measuring the diagonal of the simple wardrobe, please mark the side plates or the vertical plate of the back panel on the side panels of the simple small wardrobe to facilitate the nail backing.
3. Wardrobe assembly mid
After placing the simple wardrobe body in place, use a level ruler to measure the level of the simple wardrobe body; if it is not horizontal, please adjust it to the horizontal position.
The common method is to put things under the simple wardrobe, and then the level of the simple wardrobe cabinet can be installed in order: clothes rail, drawer, door panel or sliding door. After the telescopic mirror, install the handle according to your own simple wardrobe requirements.
After purchasing the wardrobe, everyone must assemble the work by the correct method. In some places, pay attention to it. Only in this way can we better ensure the correctness of the assembled wardrobe and make our wardrobe better. use.
Cast Iron Press,Cast Iron Waxed Press Cookware,Cast Iron Meat Press,Cast Iron Burger Press
Shijiazhuang Ever Fresh Trading Co., Ltd. , https://www.efcookwares.com